Removing Jeep Soft Top Completely – How to Remove a Jeep Soft Top Completely, foodtruckcost.com | To remove the Jeep soft top, follow these steps. First, remove the spare tire from the vehicle. Next, unscrew the door latches that secure the rear door.
If you have a hard time removing the soft top by yourself, ask a friend to help you. Once the top is removed, store it properly to keep it in good condition. To get started, read the Jeep user manual to see how to remove the safety latches.
Locate the soft top latches. The soft top latches are located on the side bows, above the door jams. Press the latches down to free the top. Lift the levers on the side to release the soft roof.
If you have a 2-door Jeep, the sun visors must be unclipped. If you have a 4-door Jeep, you can access the header latches by unclipping the sun visors.
Removing Jeep Soft Top Completely
After you’ve secured the roof latches, unfasten the two bolts holding the soft top to the brackets. You can now pull back the top from the outside.
Be sure to open the swing gate to avoid damaging the brake lamp. Then, lift the side bows by pulling on the latches.
When you’re done, slide the top down. It should come loose easily. After that, remove the latches and remove the softtop.
The process of removing a soft top is easy, and doesn’t require any special tools. You can simply lift the top and hang onto the tabs of the brackets while you take off the soft top.
Don’t forget to line the two bolts back up when you install the top. This will ensure that the top stays on the Jeep. If the top does not fit properly, you may need to get a specialist to help you.
If you have a 2-door Jeep, you should start by unclipping the soft top from the inside. Once you’ve unclipped the sun visors, unclip the header latches and fold the flap up to the roof.
Then, the soft top can be removed. Afterwards, you can carefully reinstall the top by using the same procedure. The process is easier on a two-door Jeep because it has a smaller soft-top.
The process of removing a soft-top in a 2-door Jeep involves a few steps. The first step in removing a soft top is to remove the sail flaps.
On a two-door Jeep, these flaps are located on the front and rear of the vehicle. Afterwards, you need to lift the levers on the sides of the soft-top. During this process, you will need to place the soft-top in a safe place where it will stay dry.
New 2018 Wrangler JL Soft Top Removal and Installation
To remove a soft-top from a Jeep, you must first remove the sun visors. Then, you should fold the soft-top flap to the roof. Then, you should fold the front and rear visors back to the car.
Now, the soft-top flap should be fully removed from the top of the Jeep. After removing the soft-top flaps, you can also pull the back of the soft-top.
Next, you should remove the latches on the soft-top. These are located above the front seat door jambs. Once you have removed the latches, you can slide the top toward the rear of the Jeep.
Then, the visors and the latches on the side will fall off. Then, you can remove the soft-top from the Jeep by lifting the levers on the sides.
To remove the soft-top, remove the side bows and the visors. Then, fold the front and rear flaps back and remove the soft-top. Then, you can remove the front and rear windows.
After removing the side bows, you can fold the rear window flaps. The soft-top can then be folded back to the roof. Then, you can remove the soft-top.
Before removing the Jeep soft-top, make sure you remove all the screws that secure it in place. In the case of a Jeep, this means you should remove the soft-top latches on the sides and the rear doors.
To remove the soft-top latches, untuck the rear sail panel and fold it over the roof of the Jeep. Once you have removed the panels, you can carefully pull the top out of the soft-top.